Search

Home › Bosch › Washers › E17 / F17

Bosch Washer E17 / F17 Error Code

Water is not coming in fast enough. What it means, which models show it, and how to clear it, easiest fix first.

BoschAll Bosch washer codes

E17 / F17
Easy DIY fix

The washer did not fill to the right level within the allowed time. Common causes are a closed or partly closed water tap, a kinked inlet hose, clogged inlet filters (including the filter in an AquaStop hose), or low water pressure in the home.

Compatible models

Bosch doesn't publish a model list for this code; it appears on Bosch washers with a digital display. Check your owner's manual.

Also shown as

Bosch's US code list groups E17, F17 and F29 for this problem, and its Middle East support page uses the same E17/F17 meaning. On some newer models, E:92 with -01 points to the same causes (low pressure or blocked inlet filters). A faucet icon or E:30/-10 can also signal a water supply problem (see the E:30 entry).

Difficulty

Most people can clear this one at home with simple checks.

Safety first: unplug the washer (or switch off its breaker) before touching filters, hoses or panels. If you smell burning or gas, or see water near the outlet, stop and call a professional.

How to fix Bosch E17 / F17

  1. Open the tap and check the hose

    Make sure the water tap behind the washer is turned fully on. If you need to pull the washer out to look at the inlet hose, unplug it first; if the floor around the outlet or cord is wet, switch off the washer's circuit breaker instead of touching the plug. Straighten any kink or flattened section in the hose.

  2. Check your water flow

    Bosch's US list says the tap should deliver roughly 2.5 gallons (10 L) per minute. To check, unplug the washer, close the tap, unscrew the inlet hose from it and hold a bucket under the tap, then open it fully for one minute. Much less water than that means low pressure, which a plumber should look at.

  3. Clean the inlet filters

    Turn the tap off and unplug the washer. Unscrew the inlet hose at the tap and, if accessible, at the back of the washer, then rinse the small mesh filters and brush out grit. If your hose has an AquaStop box, do not dip that box in water. Reconnect hand-tight, open the tap and check for leaks.

When to call a technician

If the tap is open, flow is normal and the filters are clean but the code keeps coming back, the water inlet valve or a sensor likely needs a technician.

Parts linked to E17 / F17

These are the parts most often behind this code. Tap one to see what it does and the signs it is failing.

Order parts by your full model number so they fit.

Frequently asked questions

What does E17 / F17 mean on a Bosch washer?

The washer did not fill to the right level within the allowed time. Common causes are a closed or partly closed water tap, a kinked inlet hose, clogged inlet filters (including the filter in an AquaStop hose), or low water pressure in the home.

Which Bosch models show the E17 / F17 code?

Bosch doesn't publish a model list for this code; it appears on Bosch washers with a digital display. Check your owner's manual.

Can I fix Bosch E17 / F17 myself?

Usually, yes. Most E17 / F17 problems clear with simple checks you can do at home. Start with the first step above: open the tap and check the hose.

What if E17 / F17 keeps coming back?

A code that returns after a reset and the checks above usually means a part is wearing out. Note when E17 / F17 appears (which cycle, how often) and have your model number ready; it helps a technician bring the right part on the first visit.

Other Bosch washer codes

Last reviewed 2026-10-19. Codes and steps can vary by model; check your owner's manual.

Sources we checked