Home › Samsung › Dishwashers › LC / LE
Samsung Dishwasher LC / LE Error Code
Leak detected. What it means, which models show it, and how to clear it, easiest fix first.
SamsungAll Samsung dishwasher codes
The leak sensor under the tub has found moisture. The dishwasher may keep running its drain pump and refuse to start a program until the base is dry. Leaking hoses, a slipped door seal, suds from the wrong detergent, or an unlevel dishwasher are common causes.
Compatible models
Samsung doesn't publish a model list for this code; it appears on Samsung dishwashers with a digital display. Check your owner's manual.
Also shown as
On Waterwall models, a blocked water reflector can also lead to LC / LE. Models without a display show it as blinking lights.
Difficulty
Start with the safe checks below; a worn part may need replacing.
How to fix Samsung LC / LE
Cut the power
Switch off the dishwasher's breaker. If water has reached the floor near an outlet or cord, use the breaker and don't touch the plug. Close the supply valve if water is actively leaking.
Find the source
Check the supply hose along its length and at both ends, then the drain hose connection under the sink. Make sure the rubber door seal is sitting in its channel. If a disposal is connected, check its knockout plug was removed.
Check detergent and leveling
Use only dishwasher detergent and don't overfill the dispenser, since leftover detergent and suds keep the sensor wet. Check the dishwasher is level; a front that sits lower than the back is a common cause of door-area leaks.
Let it dry, then restore power
Leave the dishwasher off long enough for the base to dry, especially if it was recently moved. Then restore power and see whether the code comes back.
When to call a technician
If you find a leak you can't fix by tightening a connection, or the code returns with no visible leak, request service. Internal hoses, the tub, or the sensor may need attention.
Parts linked to LC / LE
These are the parts most often behind this code. Tap one to see what it does and the signs it is failing.
- Supply hose
- Drain hose
- Door gasket
- Leak sensor
Order parts by your full model number so they fit.
Frequently asked questions
What does LC / LE mean on a Samsung dishwasher?
The leak sensor under the tub has found moisture. The dishwasher may keep running its drain pump and refuse to start a program until the base is dry. Leaking hoses, a slipped door seal, suds from the wrong detergent, or an unlevel dishwasher are common causes.
Which Samsung models show the LC / LE code?
Samsung doesn't publish a model list for this code; it appears on Samsung dishwashers with a digital display. Check your owner's manual.
Can I fix Samsung LC / LE myself?
Often. The first steps above are safe checks a homeowner can do. If they don't clear LC / LE, the cause is likely a worn part that needs replacing.
What if LC / LE keeps coming back?
A code that returns after a reset and the checks above usually means a part is wearing out. Note when LC / LE appears (which cycle, how often) and have your model number ready; it helps a technician bring the right part on the first visit.
Other Samsung dishwasher codes
- 4C / 4ENot enough water coming in
- 5C / 5E / SC / SEDishwasher is not draining
- OC / 0C / OEToo much water in the tub (overfill)
- 1E / IEClogged filter or overheating (depends on model)
- HC / HEHeater or overheating error
- tE / tCTemperature sensor error
- 3CWash pump error
- 3EIncoming water too hot (US) or pump error (UK/AU)
- 9E / 1CLow water level
- 7E / 7CWaterwall reflector blocked or misplaced
- bE / 6E / 6CStuck button
- CE / ACCommunication error between boards
- PC / PEZone Wash or Half Load error
- 9C1 / 9E1 / UCPower supply problem
- DCDoor not closed properly
- APWi-Fi setup mode (not a fault)
Last reviewed 2026-10-19. Codes and steps can vary by model; check your owner's manual.