Home › Daikin › Air Conditioners › H6
Daikin Air Conditioner H6 Error Code
Compressor position sensing error. What it means, which models show it, and how to clear it, easiest fix first.
DaikinAll Daikin air conditioner codes
The inverter board couldn't detect the compressor's rotor position, so it stopped the unit. Loose compressor wiring, a failing compressor or the outdoor board are the usual causes.
Compatible models
Daikin doesn't publish a model list for this code; it appears on Daikin air conditioners with a digital display. Check your owner's manual.
Also shown as
Daikin uses this code across its residential split, SkyAir and VRV ranges, but the exact meaning and causes can vary by series, model year and region, so confirm it in your unit's manual. How to read it: most Daikin ductless wall units only blink the operation lamp. On remotes such as the ARC433 series, press and hold the timer Cancel button for roughly 5 seconds until 00 blinks on the screen, then press Cancel again one step at a time; when the indoor unit answers with a long continuous beep, the code showing is the stored fault. SkyAir and VRV wireless remotes use a different sequence with the Inspection/Test, up/down and MODE buttons, and wired wall controllers usually show the code on their screen.
Difficulty
Try the basic checks, but the usual fix is a technician's job.
How to fix Daikin H6
Reset the power at the breaker
Switch the system off with the remote, then turn off its circuit breaker in your home's main panel. Wait about 5 minutes, switch the breaker back on and restart the unit. If the code returns within a few minutes, write it down for the technician.
Record the details for the technician
Write down the exact code, the model numbers from the labels on the indoor and outdoor units, and what the system was doing when the code appeared. Leave the unit switched off if the code keeps returning, so a fault doesn't cause further damage.
When to call a technician
H6 that returns after a reset needs a technician to test the compressor wiring and inverter board.
Parts linked to H6
These are the parts most often behind this code. Tap one to see what it does and the signs it is failing.
- compressor
- outdoor control board
Order parts by your full model number so they fit.
Frequently asked questions
What does H6 mean on a Daikin air conditioner?
The inverter board couldn't detect the compressor's rotor position, so it stopped the unit. Loose compressor wiring, a failing compressor or the outdoor board are the usual causes.
Which Daikin models show the H6 code?
Daikin doesn't publish a model list for this code; it appears on Daikin air conditioners with a digital display. Check your owner's manual.
Can I fix Daikin H6 myself?
Only the basic checks. You can safely try the steps above, but H6 usually points to a part or fault that needs a technician.
What if H6 keeps coming back?
A code that returns after a reset and the checks above usually means a part is wearing out. Note when H6 appears (which cycle, how often) and have your model number ready; it helps a technician bring the right part on the first visit.
Other Daikin air conditioner codes
- U4Indoor and outdoor units can't communicate
- U0Low refrigerant or restricted refrigerant flow
- U2Power supply voltage problem
- UAIndoor and outdoor units don't match
- A1Indoor unit control board fault
- A3Condensate water level too high
- A5Freeze-up or overheat protection
- A6Indoor fan motor fault
- C4Indoor coil temperature sensor fault
- C9Indoor room air temperature sensor fault
- E1Outdoor unit control board fault
- E5Compressor overload or lock-up protection
- E6Compressor won't start
- E7Outdoor fan motor fault
- E8Compressor current too high
- F3Compressor discharge temperature too high
- F6High pressure in cooling mode
- L4Inverter heat sink overheating
- L5Inverter output overcurrent
Last reviewed 2026-10-19. Codes and steps can vary by model; check your owner's manual.